ADIT 600

DB-9 to DB-25 female adapter

25 ft. V.35 Data Cable - male V.35 / male Winchester

10 ft. V.35 Data Cable - male V.35 / female Winchester

25 ft. V.35 Data Cable - male V.35 / female Winchester

Dual battery cable, used when using Speedway Installation Kit and 2nd Battery

2 ft. RJ45-to-RJ45 Ethernet Crossover Cable, RJ 45 plug on each end

RJ48C-to-DB15P T1 Connector Adaptor

RJ45-to-DB9P Connector Adaptor - wired with control signals

6' Cable Right Angle DB-25S (Female) to SCSI-26 (male) with Latches

25' Cable Right Angle DB-25S (Female) to SCSI-26 (male) with Latches

RJ45 Plug on one end, 10 ft. CAT 5 cable, 4 Wire E&M normal mode, 24awg

Empty 115/-48V Enclosure with backplane and 5 blank card faceplates

115/-48V Chassis, power supply, Dual T1 TDM controller, SNMP & RPM management, 5 blank card faceplates, and (1) Router Card

115/-48V Chassis, power supply, Dual T1 TDM controller, SNMP & RPM management, 4 blank card faceplates, (1) 8-port FXS card, (1) 2-port V.35 card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 4 blank card faceplates, (1) 8-port FXS card and (1) CMG Router Card

115/-48V Chassis, power supply, Dual T1 TDM controller, SNMP & RPM management, 4 blank card faceplates, (2) 8-port FXS cards

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 3 blank card faceplates, (2) 8-port FXS cards and (1) Quad T1 Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 3 blank card faceplates, (2) 8-port FXS cards and (1) CMG Router Card

115/-48V Chassis, power supply, Dual T1 TDM controller, SNMP & RPM management, 3 blank card faceplates, (3) 8-port FXS cards

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 2 blank card faceplates, (3) 8-port FXS cards and (1) Router Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 2 blank card faceplates, (3) 8-port FXS cards and (1) CMG G.729 Router Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 1 blank card faceplate, (4) 8-port FXS cards and (1) Dual V.35 Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 1 blank card faceplate, (4) 8-port FXS cards and (1) CMG Router Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, 1 blank card faceplates, (5) 8-port FXS cards

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, (5) 8-port FXS cards and (1) Dual V.35 Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, (5) 8-port FXS cards and (1) CMG Router Card

115/-48V Chassis with power supply, Dual T1 TDM controller, SNMP & RPM management, and (6) 8-port FXO cards

Adit 600, +24V Chassis, power supply, Dual T1 TDM controller, SNMP & RPM management, 5 blank card faceplates

115/-48V Chassis, power supply, Dual E1 TDM controller, SNMP & RPM management, 4 blank card faceplates, (1) Quad E1 Card and (1) Router Card

Wall Mount Kit with Swing away brackets for mounting single Adit 600 and power back-up battery. (Note: Battery UnitP/N 730-0114 must be ordered separately)

115VAC/-48VDC power supply / battery charger w/ AC cord for 115/-48V Adit 600 Base P/No. 02-AA1-000000-00 and 115/-48V Chassis P/No. 02-000-000000-00

8 channel expansion or replacement card for FXS interface applications.

Two-channel V.35 data card for connecting a router or other data equipment. Requires one V.35 cable (listed below) per port. Note: Obsolete Part - Superceded by 740-0065

Two-channel ISDN BRI card for 3DS0 LULT or LUNT applications. Note: Minimum controller software release required is Rev. 1.2.2

Single port router supporting IP/IPX routing and layer 2 bridging. Note: Minimum controller software release required is Rev. 1.4.1

8 channel expansion or replacement card for FXS interface applications. Note: Obsolete Part - Superceded by 740-0093

Two-channel V.35 data card with V.54 loopback and BERT Test Capability. Note: Minimum controller software release required is Rev. 3.0.1

Quad port all rate OCU-DP Card for DDS Service delivery applications. Note: Minimum controller software release required is Rev. 3.2.0

One controller card required per system or chassis. Includes SNMP & RPM management features. Note: Minimum E1 controller software release required is Rev. 3.2.0

Four channel DS1/E1 card for T1 voice and T1/E1 data applications. Note: Minimum controller software release required is Rev. 7.0

230V Power Supply

CMG Router Card with G.729ab low bit rate CODEC support-24 channels Note: Minimum controller software release required is Rev. 6.1

Four channel T1 card with 32Kb ADPCM voice compression on Port 1 for voice and data applications. Note: Minimum controller software release required is Rev. 7.0

Two-channel RS-232 synchronous data card with (2) 005-0166 DB-26M SCSI-to-RJ45 adapter cables. Note: Minimum controller software release required is Rev. 5.1

Software upgrade for adding G.729 to the CMG Router Card

Paper version of the Adit 600 manual

Mates with -48 DC power connector and ground studs on rear of Adit 600